Sale
  • NodeMCU ESP8266 kit to learn Arduino IoT programming,OSOYOO
  • NodeMCU ESP8266 kit to learn Arduino IoT programming,OSOYOO
  • NodeMCU ESP8266 kit to learn Arduino IoT programming,OSOYOO
  • NodeMCU ESP8266 kit to learn Arduino IoT programming,OSOYOO
  • NodeMCU ESP8266 kit to learn Arduino IoT programming,OSOYOO
  • NodeMCU ESP8266 kit to learn Arduino IoT programming,OSOYOO
  • NodeMCU ESP8266 kit to learn Arduino IoT programming,OSOYOO
  • NodeMCU ESP8266 kit to learn Arduino IoT programming,OSOYOO

NodeMCU ESP8266 kit to learn Arduino IoT programming,OSOYOO

$72.99

$33.99

This is a perfect IoT learning Kit for anyone who is looking get started with the Internet Of Things projects.

You can use this kit for DIY home improvements, science fairs, hackathons, or even to get an edge in your future career.

OSOYOO IoT Starter Kit will help you improve your practical skills for programming and electronics.  Are you ready to get started?

IoT Protocol – MQTT

MQTT is a very popular and simple protocol which is used in a lot of IoT projects.

Additionally, MQTT is widely supported by the robotics community and has many free open-source resources to help beginners on their IoT journey.

Micro Controller Board - NodeMCU

For our learning kit, we have decided to go with the NodeMCU micro controller board.

It is based on ESP8266 wifi module and is a very economical and powerful chip which fully supports WiFi and Arduino IDE. If you have Arduino programming experience, you can understand this kit in no time.

Free Tutorials Custom Made for OSOYOO IoT Started Kit

To help you get started with MQTT and IoT project, we also include a detailed DVD guide with 17 lessons.

We have come up with these 17 specific lessons, so you can take a full advantage of the OSOYOO IoT Started Kit with the least headache possible.

It includes step-by-step tutorials, circuit graphs, fully tested Arduino sample codes, videos and other nifty guides to speed up your learning process.

Best part – you can always reach out to us if you have questions!

Why OSOYOO?

We are more than a store that simply sells parts for your Arduino and Raspberry PI projects – we are an online community of programmers and robotics enthusiasts. You are welcome to visit our educational portal to learn more about robotics and look through the 100s of our online tutorials.

17 IoT Lessons for MQTT/Arduino Included (DVD + Online)

We have prepared 17 detailed lessons to get you started with MQTT. Feel free to ask us any questions if you ever get stuck!

Lesson 1: Install the ESP8266 Board Package and the Serial Port Driver
Lesson 2: Hello World!
Lesson 3: Blink an LED 
Lesson 4: Button Control LED
Lesson 5: MQTT & PubSubClient
Lesson 6: MQTT Basic Example
Lesson 7: Switch Button & MQTT
Lesson 8: DHT11 & MQTT
Lesson 9: Light Sensor & MQTT
Lesson 10: Active Buzzer & MQTT
Lesson 11: Potentiometer & MQTT 
Lesson 12: Tilt Sensor & MQTT
Lesson 13: Infrared Remote Control & MQTT
Lesson 14: 4-Digit 7 Segment LED Display & MQTT
Lesson 15: I2C 1602 LCD & MQTT
Lesson 16: Stepper Motor & MQTT
Lesson 17: Servo & MQTT

 

See the Complete List of the Lessons Below:

http://osoyoo.com/2017/05/07/osoyoo-nodemcu-iot-programming-learning-starter-kit/

 

What’s Inside?

  • 1x ESP8266 WIFI NodeMCU Board
  • 1x Micro USB cable
  • 1x I2C 1602 LCD Display
  • 1x SG90 Servo Motor
  • 1x DHT11 Temperature & Humidity Sensor Module
  • 1x SW520D Tilt Sensor
  • 1x 4-Digit 7 Segment LED Display module
  • 1x Stepper Motor + Bridge
  • 3x Potentiometer (10kilohm adjustable resistor)
  • 1x Buzzer
  • 3x GL5516 Photoresistor (Light Sensor)
  • 1x Infrared Receiver (VS1838B)
  • 1x Infrared Remote Controller
  • 24x LED (6x White, 6x Red, 6x Yellow, 6x Green)
  • 5x Push Buttons
  • 5x Push Button Hats
  • 1x Breadboard
  • 1x 4AA Battery Holder
  • 65x Resistors (20x 200ohm, 20x 10Kohm, 20x 1Kohm, 5x1Mohm)
  • 40 Pin Jumper Wires (15cm, Male to Male)
  • 16 Pin Jumper Wires (20cm, Female to Female)
  • 1x Plastic Box