7inch DSI PNP Touch Screen IPS LCD for Raspberry Pi No need Driver!

The OSOYOO 7-inch IPS DSI touchscreen connects to your Raspberry Pi through the DSI connector. It is a capacitive touch LCD with a physical resolution of 800×480. It is plug-and-play — no driver installation needed. The IPS panel provides wide viewing angles and reduces glare and reflections, so colours stay vivid and consistent even when viewed from extreme angles.

Why DSI?

• One cable does it all: display signal and touch travel over the single DSI ribbon cable, and the screen draws power directly from the board — no external power source needed.
• No GPIO occupied: unlike SPI screens, it does not use the SPI bus or any GPIO pins, so you can work on your DIY IoT projects while using the screen at the same time.
• No HDMI needed: the same clarity as an HDMI screen, without taking the HDMI port and without any HDMI licence cost.
• Driver-free: connect the cable, power on, and the screen just works.

Features

• 7" IPS LCD with 800 × 480 physical resolution, 24-bit colour and 60 Hz refresh rate
• Wide 170° viewing angle (85°/85°/85°/85°) with vivid IPS colours
• 5-finger capacitive touch (note: Raspbian currently supports only 1 finger at a time)
• Virtual resolution adjustable from 800 × 480 up to 1920 × 1080 on Raspberry Pi Legacy OS
• Strong anti-interference design, ultra-low power consumption, ultra-long-distance lossless signal transmission, auto-sleep function
• Compatible with Raspberry Pi OS, Ubuntu MATE, Kali, RetroPie, OctoPrint, and more
• Compatible with Raspberry Pi 5, 4, 3, and Compute Modules CM4 / CM3
• Lightweight and compact — an ideal choice for portable Raspberry Pi projects, from mobile stations to field-ready devices
• Easily mount your Raspberry Pi to the exposed backside of the touch screen

Specifications

• Display: 7" IPS LCD, capacitive touch
• Physical resolution: 800 × 480, 24-bit colour
• Refresh rate: 60 Hz
• Touch: 5-finger capacitive (1 finger under Raspbian)
• Viewing angle: 85° / 85° / 85° / 85°
• Interface: DSI (MIPI)
• Compatible boards: Raspberry Pi 5 / 4 / 3, CM4 / CM3

What's in the box?

• 1 × 7" DSI touch LCD screen for Raspberry Pi
• 1 × 15-pin to 15-pin DSI FFC cable for Raspberry Pi 2/3/4
• 1 × 15-pin 1 mm to 22-pin 0.5 mm DSI FPC cable for Raspberry Pi 5
• 1 × screwdriver, 4 × screws
• 1 × user guide manual

Please note

• The DSI port of the OSOYOO 7-inch DSI screen is the same as the official Raspberry Pi 7-inch DSI screen, and this screen is compatible with the DSI cable for the official screen. When installing the cable, the 15-pin 1 mm end goes into the screen's DSI port with the metal contacts facing upward — please pay attention to the contact points at the end of the cable.
• Adjusting the virtual resolution and the display orientation works on Raspberry Pi Legacy OS only; on Bookworm the DSI screen does not support resolution adjustment. If you are using a Raspberry Pi 4, comment out the line `#dtoverlay=vc4-kms-v3d` in `/boot/config.txt` when adjusting the virtual resolution.
• Brightness can be adjusted on Raspbian with `echo 100 > /sys/class/backlight/rpi_backlight/brightness` (replace 100 with any value from 0 to 255). If brightness adjustment fails, check whether the line `disable_touchscreen=1` exists in `/boot/config.txt` and comment it out.
• An on-screen virtual keyboard can be added (matchbox-keyboard) if you want to type without a USB keyboard.
• Make sure your micro SD card has enough free space for the system image, and do not touch your Raspberry Pi board when the power is on or when your hands carry a static charge (discharge static by touching a metal faucet).

PiStudio variant products: PiStudio Case + OSOYOO 7-inch V4.0 Screen · PiStudio Case without Screen

Tutorial: OSOYOO 7″ IPS DSI Touch Screen for Raspberry Pi (Model 2024003600)
Datasheet: Dimension datasheet (PDF)